1. 根目录:
2. arch
3. arm
4. plat-samsung
5. Makefile

# arch/arm/plat-s3c64xx/Makefile
#
# Copyright 2009 Simtec Electronics
#
# Licensed under GPLv2

obj-y				:=
obj-m				:=
obj-n				:= dummy.o
obj-				:=

# Objects we always build independent of SoC choice

obj-y				+= init.o
obj-$(CONFIG_ARCH_USES_GETTIMEOFFSET)   += time.o
obj-y				+= clock.o
obj-y				+= pwm-clock.o
obj-y				+= gpio.o
obj-y				+= gpio-config.o
obj-y				+= dev-asocdma.o

obj-$(CONFIG_SAMSUNG_GPIOLIB_4BIT)	+= gpiolib.o
obj-$(CONFIG_SAMSUNG_CLKSRC)	+= clock-clksrc.o

obj-$(CONFIG_SAMSUNG_IRQ_UART)	+= irq-uart.o
obj-$(CONFIG_SAMSUNG_IRQ_VIC_TIMER) += irq-vic-timer.o

# ADC

obj-$(CONFIG_S3C_ADC)	+= adc.o

# devices

obj-y				+= platformdata.o

obj-$(CONFIG_S3C_DEV_HSMMC)	+= dev-hsmmc.o
obj-$(CONFIG_S3C_DEV_HSMMC1)	+= dev-hsmmc1.o
obj-$(CONFIG_S3C_DEV_HSMMC2)	+= dev-hsmmc2.o
obj-$(CONFIG_S3C_DEV_HSMMC3)	+= dev-hsmmc3.o
obj-$(CONFIG_S3C_DEV_HWMON)	+= dev-hwmon.o
obj-y				+= dev-i2c0.o
obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
obj-$(CONFIG_S3C_DEV_I2C2)	+= dev-i2c2.o
obj-$(CONFIG_S3C_DEV_I2C3)	+= dev-i2c3.o
obj-$(CONFIG_S3C_DEV_I2C4)	+= dev-i2c4.o
obj-$(CONFIG_S3C_DEV_I2C5)	+= dev-i2c5.o
obj-$(CONFIG_S3C_DEV_I2C6)	+= dev-i2c6.o
obj-$(CONFIG_S3C_DEV_I2C7)	+= dev-i2c7.o
obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
obj-y				+= dev-uart.o
obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o
obj-$(CONFIG_S3C_DEV_WDT)	+= dev-wdt.o
obj-$(CONFIG_S3C_DEV_NAND)	+= dev-nand.o
obj-$(CONFIG_S3C_DEV_ONENAND)	+= dev-onenand.o
obj-$(CONFIG_S3C_DEV_RTC)	+= dev-rtc.o

obj-$(CONFIG_SAMSUNG_DEV_ADC)	+= dev-adc.o
obj-$(CONFIG_SAMSUNG_DEV_IDE)	+= dev-ide.o
obj-$(CONFIG_SAMSUNG_DEV_TS)	+= dev-ts.o
obj-$(CONFIG_SAMSUNG_DEV_KEYPAD)	+= dev-keypad.o
obj-$(CONFIG_SAMSUNG_DEV_PWM)	+= dev-pwm.o

# DMA support

obj-$(CONFIG_S3C_DMA)		+= dma.o

obj-$(CONFIG_S3C_PL330_DMA)	+= s3c-pl330.o

# PM support

obj-$(CONFIG_PM)		+= pm.o
obj-$(CONFIG_PM)		+= pm-gpio.o
obj-$(CONFIG_SAMSUNG_PM_CHECK)	+= pm-check.o

obj-$(CONFIG_SAMSUNG_WAKEMASK)	+= wakeup-mask.o

# PD support

obj-$(CONFIG_SAMSUNG_PD)	+= pd.o

# PWM support

obj-$(CONFIG_HAVE_PWM)		+= pwm.o